FAQ
Below you will find a list of the most frequently asked questions.Should you be unable to find the answer to your particular question, or should you need expert advice regarding Nilfisk FOOD products do not hesitate to contact us.
Filter by type:
The size of the colored chemical limiting nozzles (item no 0614213)?
Answer:
| Inch | mm | Color |
| .125 | 3,175 | Grey |
| .098 | 2,4892 | Black |
| .070 | 1,778 | Beige |
| .062 | 1,5748 | Red |
| .052 | 1,3208 | White |
| .040 | 1,016 | Blue |
| .035 | 0,889 | Tan |
| .028 | 0,7112 | Green |
| .025 | 0,635 | Orange |
| .023 | 0,5842 | Brown |
| .020 | 0,508 | Yellow |
| .016 | 0,5064 | Turquoise |
| .014 | 0,3556 | purple |
| .012 | 0,3048 | Light blue |
| .010 | 0,254 | Pink |
| Drill to size | Clear |
Why is the foam quality very thin?
Answer:
Ensure sufficient chemical supply.
Try changing the type of chemical detergent used.
Try changing the type of chemical detergent used.
Why does the green and the red display lamp light up and Im unable to operate the cleaning unit?
Answer:
When both the red and the green lamp are turned on when you start your cleaning station, it means that there is an issue with the battery.
To solve the problem do the following:
1. Switch off the main power to the cleaning station
2. Wait for 3 minutes (do not turn on the machine within this time)
3. Press the "left arrow" button and at the same time turn on the main power to the cleaning station (Do the two actions at the same time)
4. The problems is resolved now; the display is in the "normal mode" and should charge the internal battery
5. To test: After 15 minutes try to switch off the main power and wait for three minutes, then turn it on again. If the problem is not solved, it means that the display is broken/dead.
To solve the problem do the following:
1. Switch off the main power to the cleaning station
2. Wait for 3 minutes (do not turn on the machine within this time)
3. Press the "left arrow" button and at the same time turn on the main power to the cleaning station (Do the two actions at the same time)
4. The problems is resolved now; the display is in the "normal mode" and should charge the internal battery
5. To test: After 15 minutes try to switch off the main power and wait for three minutes, then turn it on again. If the problem is not solved, it means that the display is broken/dead.
Why is there water in the air hoses?
Answer:
The non-return valve for air is dirty.
Clean or replace the valve.
Clean or replace the valve.
Why is there water in the supply of chemical?
Answer:
The non-return valve for chemicals is dirty.
Clean or replace the valve.
Clean or replace the valve.
Why is there air in the water supply ?
Answer:
The non-return valve for water is dirty.
Clean or replace the valve.
Clean or replace the valve.
Why is there no foam/suction ?
Answer:
Most likely there is dirt/debris inside the injector.
Clean or replace the injector.
Clean or replace the injector.
Why is the foam pulsing ?
Answer:
The air pressure is too high.
Lower the pressure.
Lower the pressure.
What kind of stainless steel is the manifold made of?
Answer:
The manifold is made of AISI 304 steel.
Are User-packs mounted directly on the cleaning station?
Answer:
No.
User packs are mounted below or beside the cleaning station,
User packs are an accessory and must be ordered seperately.
User packs are mounted below or beside the cleaning station,
User packs are an accessory and must be ordered seperately.
